ELECTRIC POWER DIVISION
변압기 무선부하 감시시스템(DTMS), 고장전류경로감시 시스템(FPI), POWER CT
This, where installed, will provide a mean of indicating the passage of fault current along the medium voltage overhead line and It shall be made of Fault detection systems with LED falsh0ing and wireless communication to be installed on Medium Voltage Overhead Electric networks. It must be positioned in strategic locations, for example at the start of each branch and at the location of manual switchgear. Send fault location message to pre-set person
Feature
- It is designed monitoring of overhead MV line
- The LED indicates fault type as permanent and transient
- Set up parameter by RF modem
Description
- Easy to detect fault location on MV line and do faster recovery
- LED light is visible from a 360⁰
Inrush filtering
- It depends whether it is inactive or active in case that the current on conductor is higher than pre-set fault current.
Reset
- By FCS program / By Magnetic / Reset after the set time has elapsed
Advantages
- Improve revenue by shorten rounding time & recovery time
- Reduce consumer complaining by outage managemen
Detection
- Voltage : Measured voltage by non-contacting CT at magnetic field on live conductor.
- Current : Measured current by non-contacting sensor at magnetic field on live conductor.
Fault type
- Inrush, Transient and Permanent fault
Fault confirmation
- Operating center : Alert by RF & GSPR communication
- A field : LED ON/OFF status
Characteristic
- Distribution network voltage : 7 kV to 40 kV Conductor diameter Size
- Conductor diameter Size
Fault detection – parameters
- Inrush restraint duration : 3s
- Loss of voltage condition : < 40 % 40, 50, 100, 200, 400 Voltage drop from 3s to 100s after fault detection
- Permanent fault
- Fault confirmation
Reset
- Light power : 1~24 hours
- Manual reset : by manual and monitoring program on computer
Fault indication
- Signalisation : Red flash light
- Light power : 40 lumens
- Visibility angle : 360°
- Flash period for permanent fault : (0.1~0.5) s every (5~30s) [1 to 24h ] 1,000 hours
- Standard total flash duration : > 7 years
- Lithium battery life cycle
Setting item
- Set GrID, PoleID, ToID, frequency, Fault current limit, Fault detect time, Total LED operating time, LED operating interval after LED ON.
- Complete setting and start self-transmission automatically
Wake Up
- Approach magnetic to Reed S/W at least 2 second
- Operate self-transmission if it does not set
- Go to sleep mode after self-transmission ten times if it does set
Sleep mode
- It goes to sleep mode after complete FCS set
- Set time at FCS initialize : ex) 2 min / No.1 select , 10 min / No.2 select
Self-transmission
- Start self-transmission according to wake up call (10 times)
- Self-transmission interval : 6s
Notice presence status
- Auto converting from Sleep Mode to Active Mode at pre-set time
- Notice delay time : FCS ID * 3s : ex) No. 1 = 3초, No. 9 = 27s
RF modem : ON
- Data : Battery current, floating current, inactive/ active
- Retry : 12s interval , 5 times(1 min)
- Time synchronize after receive command from master
- Notice fault if fault current and inactive on conductor
- Retry when communication failure : 12s interval, 5 times(1 min)
RF modem : OFF
- Active Mode -> Sleep Mode
Notice fault status
- Occurring fault current at minimum 3 cycle : Sleep Mode -> Active Mode
- Fault current parameter
- Identify floating Voltage during fault decision duration.
- Decide inactive or active voltage on conductor during fault decision duration
- Archive Current parameter after pass fault decision duration
LED operating
- Wake Up : Lighting from No. 1 LED to No. 8 LED in serial order
- Fault current : Operate according to set interval and duration time
- Fault reset : Blinking 10 times (0.2s ON/ 0.2s OFF)
Time synchronize
- After Master response
- Synchronized PC time when set parameter by FCS monitoring program
- Automatic reset on voltage recovery : 0[S] ~ 70[S]
- Long duration automatic reset : 5[mm] ~ 35[mm]
- Manual reset : 3[S]
- Remote reset : 50[Hz], 60[Hz]
- Display : 3[A] ~ 650[A]
- Light Power : 100[A] ~ 600[A]
- Visibility angle : 5[S] ~ 70[S]
- Frequency : 10 events
- Sensitivity : 15[A], 20[A], 30[A], 40[A], 60[A], 70[A], 80[A
- Maximum distance : 200[m]
- Lithium battery : 3.6[V], 19000[mA]
- Battery duration : minimum 8 years
- Operating temperature : -20[℃] ~ +70[℃]
- Storage temperature : -40[℃] ~ +85[℃]
- Humidity : < 95[%]
- Protection level : IP 65
- Interval time of sending data : 1 hour
- Measuring time : every 3(s)
- Numbers of sample per hour : 1200=3600(s)/3(s)
- To detect phase-to-phase and phase-to-earth fault currents on the MV network.
- To detect voltage active or inactive
- To transmit fault information to the control center spontaneously via the GPRS
- To provide LED light indication of fault.
- Can see install site at google map
- To provide operators with all useful information for fault finding
SCADA
- It is designed monitoring of outdoor on MV line
- The LED indicates fault type as Phase to phase and Earth fault
- Set up parameter by Web or Dip Switch
- Self reset after recovery or manual reset
- Set fault range 10A to 100A
- Operating by built-in battery
| Frequency | 50Hz and 60Hz |
|---|---|
| Fault Type | Phase to Phase fault/ Phase to earth |
| Load | > 2A |
| Phase fault | 100 to 800A |
| Earth fault | 20 to 160A |
| Fault acknowledge Time delay | 40ms |
| Confirmation time delay | 70s |
| Inrush time delay | 3s |
| Reset | Auto (upon current return 2A) Manual via front panel / External contact (web) |
| Indication | LED |
| Battery | Lithium |
| Display | 4-digit LCD / Fault : RED |
| Phase CT | Spilit CTs |
전체 2
| 번호 | 제목 | 작성자 | 작성일 | 추천 | 조회 |
| 2 |
FPI MINI SCADA MANUAL
admin
|
2019.10.08
|
추천 0
|
조회 1
|
admin | 2019.10.08 | 0 | 1 |
| 1 |
FPI WEB SCADA Manual
admin
|
2019.10.08
|
추천 0
|
조회 2
|
admin | 2019.10.08 | 0 | 2 |
- WKFPI-SF
-
This, where installed, will provide a mean of indicating the passage of fault current along the medium voltage overhead line and It shall be made of Fault detection systems with LED falsh0ing and wireless communication to be installed on Medium Voltage Overhead Electric networks. It must be positioned in strategic locations, for example at the start of each branch and at the location of manual switchgear. Send fault location message to pre-set person
Feature
- It is designed monitoring of overhead MV line
- The LED indicates fault type as permanent and transient
- Set up parameter by RF modem
Description
- Easy to detect fault location on MV line and do faster recovery
- LED light is visible from a 360⁰
Inrush filtering
- It depends whether it is inactive or active in case that the current on conductor is higher than pre-set fault current.
Reset
- By FCS program / By Magnetic / Reset after the set time has elapsed
Advantages
- Improve revenue by shorten rounding time & recovery time
- Reduce consumer complaining by outage managemen
Detection
- Voltage : Measured voltage by non-contacting CT at magnetic field on live conductor.
- Current : Measured current by non-contacting sensor at magnetic field on live conductor.
Fault type
- Inrush, Transient and Permanent fault
Fault confirmation
- Operating center : Alert by RF & GSPR communication
- A field : LED ON/OFF status
Characteristic
- Distribution network voltage : 7 kV to 40 kV Conductor diameter Size
- Conductor diameter Size
Fault detection – parameters
- Inrush restraint duration : 3s
- Loss of voltage condition : < 40 % 40, 50, 100, 200, 400 Voltage drop from 3s to 100s after fault detection
- Permanent fault
- Fault confirmation
Reset
- Light power : 1~24 hours
- Manual reset : by manual and monitoring program on computer
Fault indication
- Signalisation : Red flash light
- Light power : 40 lumens
- Visibility angle : 360°
- Flash period for permanent fault : (0.1~0.5) s every (5~30s) [1 to 24h ] 1,000 hours
- Standard total flash duration : > 7 years
- Lithium battery life cycle
Setting item
- Set GrID, PoleID, ToID, frequency, Fault current limit, Fault detect time, Total LED operating time, LED operating interval after LED ON.
- Complete setting and start self-transmission automatically
Wake Up
- Approach magnetic to Reed S/W at least 2 second
- Operate self-transmission if it does not set
- Go to sleep mode after self-transmission ten times if it does set
Sleep mode
- It goes to sleep mode after complete FCS set
- Set time at FCS initialize : ex) 2 min / No.1 select , 10 min / No.2 select
Self-transmission
- Start self-transmission according to wake up call (10 times)
- Self-transmission interval : 6s
Notice presence status
- Auto converting from Sleep Mode to Active Mode at pre-set time
- Notice delay time : FCS ID * 3s : ex) No. 1 = 3초, No. 9 = 27s
RF modem : ON
- Data : Battery current, floating current, inactive/ active
- Retry : 12s interval , 5 times(1 min)
- Time synchronize after receive command from master
- Notice fault if fault current and inactive on conductor
- Retry when communication failure : 12s interval, 5 times(1 min)
RF modem : OFF
- Active Mode -> Sleep Mode
Notice fault status
- Occurring fault current at minimum 3 cycle : Sleep Mode -> Active Mode
- Fault current parameter
- Identify floating Voltage during fault decision duration.
- Decide inactive or active voltage on conductor during fault decision duration
- Archive Current parameter after pass fault decision duration
LED operating
- Wake Up : Lighting from No. 1 LED to No. 8 LED in serial order
- Fault current : Operate according to set interval and duration time
- Fault reset : Blinking 10 times (0.2s ON/ 0.2s OFF)
Time synchronize
- After Master response
- Synchronized PC time when set parameter by FCS monitoring program
- WKFPI-SC / RTU
-
- Automatic reset on voltage recovery : 0[S] ~ 70[S]
- Long duration automatic reset : 5[mm] ~ 35[mm]
- Manual reset : 3[S]
- Remote reset : 50[Hz], 60[Hz]
- Display : 3[A] ~ 650[A]
- Light Power : 100[A] ~ 600[A]
- Visibility angle : 5[S] ~ 70[S]
- Frequency : 10 events
- Sensitivity : 15[A], 20[A], 30[A], 40[A], 60[A], 70[A], 80[A
- Maximum distance : 200[m]
- Lithium battery : 3.6[V], 19000[mA]
- Battery duration : minimum 8 years
- Operating temperature : -20[℃] ~ +70[℃]
- Storage temperature : -40[℃] ~ +85[℃]
- Humidity : < 95[%]
- Protection level : IP 65
- Interval time of sending data : 1 hour
- Measuring time : every 3(s)
- Numbers of sample per hour : 1200=3600(s)/3(s)
- To detect phase-to-phase and phase-to-earth fault currents on the MV network.
- To detect voltage active or inactive
- To transmit fault information to the control center spontaneously via the GPRS
- To provide LED light indication of fault.
- Can see install site at google map
- To provide operators with all useful information for fault finding
SCADA
- WKFPI-EFI
-
- It is designed monitoring of outdoor on MV line
- The LED indicates fault type as Phase to phase and Earth fault
- Set up parameter by Web or Dip Switch
- Self reset after recovery or manual reset
- Set fault range 10A to 100A
- Operating by built-in battery
Frequency 50Hz and 60Hz Fault Type Phase to Phase fault/ Phase to earth Load > 2A Phase fault 100 to 800A Earth fault 20 to 160A Fault acknowledge Time delay 40ms Confirmation time delay 70s Inrush time delay 3s Reset Auto (upon current return 2A)
Manual via front panel / External contact (web)Indication LED Battery Lithium Display 4-digit LCD / Fault : RED Phase CT Spilit CTs - Server
-
- Archive
-
전체 2
번호 제목 작성자 작성일 추천 조회 2 FPI MINI SCADA MANUALadmin | 2019.10.08 | 추천 0 | 조회 1admin 2019.10.08 0 1 1 FPI WEB SCADA Manualadmin | 2019.10.08 | 추천 0 | 조회 2admin 2019.10.08 0 2